FAAC Gate Installation Nationwide

FAAC Gate Installation in Henderson: What to Know First

FAAC gate installation in Henderson typically runs $2,800 to $7,500 for a complete swing or slide gate system, including the operator, gate fabrication, safety devices, and labor. Most installations take two to four days from site survey to final test, depending on whether you’re replacing an existing operator or building new from the slab up. We quote a written price before any work begins, and that number doesn’t move unless you change the scope.

Call (775) 307-6571

We’re an independent FAAC service provider, not a factory-authorized dealer, which means we call problems the way we see them and stock parts from multiple suppliers instead of one corporate channel. This page is for Henderson homeowners who already own or are considering a FAAC system and want straight answers about installation, failure points, and real cost. Call (775) 307-6571 and a live person picks up, day or night.

How FAAC Products Fail – and How We Fix Them

FAAC builds a solid operator. But every brand has patterns, and after years working on them in Henderson, here’s what we actually see:

• FAAC 400 and 402 swing operators: capacitor failure after 5-7 years. The 400-series uses a start capacitor that’s prone to swelling in sustained heat. Here in Henderson, where summer temperatures sit above 100°F for weeks, these capacitors cook faster than in coastal climates. The symptom is an operator that hums but won’t start, or starts only when you push the gate. We replace with a higher-temperature-rated capacitor, not the factory part, which extends the life another several years.
• FAAC 844 slide operators: limit switch drift on long runs. The 844 is a workhorse on commercial and long residential drives, but its mechanical limit switches wear and drift on runs over 30 feet. The gate stops short or overtravels and slams the end stop. We reset limits, inspect the rack and pinion engagement, and replace the switch assembly when the cam faces are grooved. This is a two-hour fix most of the time, not an operator replacement.
• FAAC S700H and S800H: hydraulic pump seal weep in cold snaps. Henderson winters aren’t brutal, but the freeze-thaw around December and January is enough to stress older hydraulic seals. You’ll see a fine film of oil under the operator cover or on the piston shaft. Left alone, it starves the pump and burns the motor. We catch this during installation work on adjacent systems all the time. New seal kit, fresh fluid, and a pressure test usually resolves it.
• FAAC E024U control boards: photocell input faults caused by spade connector corrosion. This is the classic FAAC head-scratcher. The board flashes a photocell fault even though the photo eyes are aligned and clean. The real cause is often corrosion at the board’s spade terminals, not the photocells themselves. We disconnect, clean, reseat, and seal the terminals with dielectric grease. Dozens of homeowners have paid for a board replacement elsewhere when the fix was a $2 connector service.
• FAAC articulating arm operators: bushing wear on the pivot points. On the FAAC 390 and 412, the articulating arm joints have bronze bushings that wear out long before the motor does. The gate starts to sag, the arm chatters on closing, and the motor works harder. We replace the bushing set and rebalance the gate leaves, which usually brings operation back to factory spec without touching the operator itself.

Lonnie Burke has a saying about FAAC diagnostics: “Tell me what it’s doing wrong, and I’ll tell you what it needs – usually those are two different things.” We’ve earned a lot of repeat work in Henderson by fixing the actual problem instead of selling the operator swap.

Our FAAC Gate Installation Process

Every FAAC installation follows the same sequence, whether it’s a new driveway gate in Seven Hills or a pedestrian gate in Green Valley Ranch:

1. 1
   Site survey and measurement. We measure the opening, check post condition, verify power availability, and look at drainage. Henderson soil shifts, and a slab that’s moved half an inch changes everything about operator mounting.
2. 2
   Written quote. You get a line-item price before any work starts. Operator, gate fabrication, safety edges, photo eyes, loop detectors, conduit, labor. The number on that sheet is the number you pay.
3. 3
   Operator selection and parts sourcing. If the existing FAAC operator is sound, we install the gate around it and save you money. If you need a new operator, we match the model to the gate weight, width, and duty cycle, and we source OEM FAAC components or a quality aftermarket equivalent depending on warranty status and availability.
4. 4
   Installation. Gate hung, operator mounted, arm or chain connected, safety edges and photo eyes installed, control board wired and programmed. We set opening and closing speeds, soft-start and soft-stop, and auto-close timing.
5. 5
   Full test cycle. We run the gate through 20-plus cycles including obstruction reversal, edge contact, manual release, and power interruption. We don’t leave until the gate operates the same on open number 20 as it did on open number 1.
6. 6
   Walkthrough and documentation. We show you how to operate and release the gate manually, explain your safety devices, and leave you with the written guarantee covering the installation for a full year.

We clean the site before we leave. Cut metal, old parts, packaging – it goes with us, not into your landscaping.

What FAAC Gate Installation Costs in Henderson

Real numbers, because you should know before you call:

• Pedestrian gate with FAAC 390 operator: $2,800 – $4,200 installed
• Single swing driveway gate with FAAC 400: $3,500 – $5,500 installed
• Double swing gate with FAAC 412 or 415: $4,800 – $7,200 installed
• Slide gate with FAAC 844: $4,500 – $7,500 installed
• Solar-powered FAAC setup (no grid power at the gate): add $800 – $1,500

What moves the price: gate size and weight, post condition, whether we’re running new conduit or using existing, and whether the control board and safety devices are staying or getting replaced. A gate built for a 16-foot opening in Anthem with steel posts set in concrete costs more than a 10-foot pedestrian gate off a masonry wall near Horizon Ridge. Call (775) 307-6571 for a written quote – estimates are free, and the price is agreed before we touch anything.

Why Henderson Homeowners Call Carver Gate Repair Henderson for FAAC Work

We’re gate specialists. Not landscapers who also do gates, not general contractors who fit one in between kitchen remodels. Carver Gate Repair Henderson works exclusively on gates and gate motors, and every technician is background-checked, uniformed, and trained on FAAC specifically alongside LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. If your FAAC operator goes down and parts are back-ordered, we can tell you honestly whether a different brand’s operator fits your gate and budget.

Every repair and installation carries our 365-Day Done Right Promise in writing. If something fails inside that year, the second visit is free – no charge, no argument. We’ve been operating to the Garrison Standard since 2008, and that standard doesn’t change from job to job or neighborhood to neighborhood. The way we work in Anthem is the same way we work along the Raiders practice corridor: written price, clean site, gate that works when we leave.

FAQs