Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Motor Repair for Henderson Homeowners
A gate motor that won’t open, grinds when it moves, or opens halfway and stops is more than an inconvenience. It’s a security gap and a daily hassle, especially in Henderson where afternoon heat and desert dust shorten the life of electronic components. Carver Gate Repair Henderson fixes gate motors the right way, with a written price before work starts and a full-year guarantee on every repair. We answer the phone 24/7 at (775) 307-6571, so when a motor fails on a Saturday night or a holiday morning, a live person picks up. Lonnie Burke leads our Henderson crew, and every technician shows up background-checked and in uniform.
We focus exclusively on gates and gate motors. Not fences, not garage doors, not general contracting. That focus means our technicians see more swing arms, limit switches, and circuit boards in a month than most contractors see in a year. If you’re in Henderson, Green Valley, Anthem, or any neighborhood east of the Strip, we can diagnose your gate motor and give you a written quote, usually the same day you call.
Key Takeaways
- Written price before any work starts. The number on the quote is the number on the invoice. No surprises.
- Full-year guarantee on every gate motor repair. If it fails within 365 days, we come back and fix it free.
- Nine gate-motor brands serviced. LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
- Live-person phone coverage 24/7/365. Call (775) 307-6571 any hour, any day.
- Free estimates with no dispatch fee. We quote before we touch a wrench.
Styles & brands we work with
Gate Motor
Gate Motor is the powered operator that opens and closes your driveway or pedestrian gate, typically an electromechanical arm, a slide operator, or an underground piston depending on the gate type. In Henderson, summers routinely hit 105°F or higher, and that heat bakes capacitors, control boards, and gear grease until they degrade. You need gate motor service when the gate moves slower than it used to, stalls mid-travel, hums without moving, or smells like burned electronics near the operator housing. Carver Gate Repair Henderson diagnoses the specific failure point: limit switch drift, capacitor failure, stripped gears, or a seized arm. Most motor repairs in Henderson run $180 to $650 depending on the part and the operator type, and a full motor replacement typically runs $650 to $2,400 for the unit plus installation. We give you a written price before we start, every time.
Overheating and Thermal Cutout
Henderson’s summer sun cooks motors mounted on west-facing columns. When a motor overheats, it triggers a thermal cutoff and refuses to run until it cools, which can take an hour or more.
We check the housing ventilation, test the capacitor, and confirm whether the motor is drawing excessive current. Sometimes the fix is a replacement capacitor; other times the motor itself is fatigued and needs swapping before it burns out entirely.
Underground Operator Failure
Underground gate motors in Henderson have a rough life. Irrigation runoff, caliche soil, and monsoon-season moisture work their way into the housing and corrode the internals.
Carver Gate Repair Henderson pulls the operator, inspects the seals and weep holes, and replaces the motor assembly when water intrusion has done its damage. We’ll tell you plainly if the housing can be salvaged or if a surface-mount conversion makes more financial sense.
Gate Remote Control
Gate Remote Control is the handheld or visor-clipped transmitter that sends a radio signal to your gate operator’s receiver, telling it to open or close. When a remote controls nothing but a blinking LED, works only from three feet away, or works intermittently, the problem is usually the remote battery, the receiver antenna, or interference from nearby sources. In Henderson neighborhoods like Anthem and Green Valley, we see a lot of conflict with HOA gate systems, solar chargers, and wireless security gear operating on adjacent frequencies. A replacement remote for a LiftMaster or FAAC system in Henderson typically runs $60 to $160, and adding or reprogramming remotes runs $85 to $145 including the service call. Carver Gate Repair Henderson matches the remote’s frequency and copy-protection protocol to your existing operator, so you don’t buy a box of parts that won’t pair.
Lost and Missing Remotes
When a remote goes missing, the security concern is real: whoever has the remote can open your gate until it’s deleted from the operator’s memory.
We wipe stored transmitter codes from the receiver, re-add the remotes you still have, and program new ones on the spot. Most operators in Henderson hold 20 to 200 transmitter slots, so clearing and reprogramming takes under an hour.
Commercial and Multi-Button Remotes
If you have a multi-gate property or need one remote to operate two entrances, a three-button or four-button remote is the answer. The buttons can be mapped to separate operators, separate gates, or even a pedestrian gate and a vehicle gate.
We program each button to the correct channel on your LiftMaster, Linear, or FAAC receiver and test range from the street and the driveway. The same written-price rule applies: you approve the cost before we order anything.
Gate Keypad
Gate Keypad is the weatherproof numeric pad mounted on a pedestal or column that opens the gate when a valid PIN is entered. Keypads fail in Henderson for predictable reasons: sun-brittle membrane buttons, dust inside the contacts, corroded wiring terminals, and code drift that spits out valid PINs after a power blip. You need service when the keypad beeps but doesn’t activate the gate, when some digits don’t register, or when the backlight dies at night. A new wired or wireless gate keypad in Henderson runs $180 to $420 installed, and reprogramming an existing keypad runs $95 to $145. Carver Gate Repair Henderson installs keypads from LiftMaster, FAAC, and Linear, wired to the operator or paired wirelessly depending on your gate controller.
Wireless vs. Wired Keypads
Wireless keypads are easier to install but eat through batteries faster in Henderson’s summer heat. Wired keypads last longer but require a conduit run from the pedestal to the operator.
We look at the distance, the existing conduit, and your power situation before recommending one over the other. We don’t push wireless just because it’s faster for us.
High-Traffic and Pedestrian Keypads
A keypad that serves a pedestrian gate for a community or a rear-access alley takes far more abuse than one used twice a day at a single-family driveway. Buttons wear out, the housing cracks, and water finds its way in.
We can rebuild the keypad with new buttons and seals, or replace the unit with a commercial-grade keypad rated for continuous outdoor exposure. Either way, the repair carries the same 365-day Done Right Promise.
Gate Closer Spring
Gate Closer Spring is the tensioned hardware, often a pair of coil springs or a torsion assembly, that pulls a swing gate closed when the operator releases it or when the gate is opened manually. In Henderson, dry air and temperature swings cause these springs to lose tension, rust at the anchors, or snap outright. Symptoms you’ll notice: the gate drifts open an inch or two after closing, slams shut on a windy day, or the operator labors and trips its current sensor because the spring load is off. Replacing a gate closer spring in Henderson typically runs $120 to $280 for a standard single-spring setup and $280 to $600 for a heavy ornamental or double-spring gate. Carver Gate Repair Henderson adjusts tension to match your operator’s force curve, so the gate closes firmly without fighting the motor.
Tension and Travel Adjustment
A spring that’s too tight turns your gate into a hazard: it slams with enough force to injure a person or a pet. Too loose, and the operator works double-time to finish the close cycle.
We set the spring tension while measuring the gate’s closing force, not by feel. The gate should hold closed under wind load but open without a battle.
Corner and End Bracket Wear
The springs themselves aren’t always the failure point. We regularly replace worn corner brackets and end anchors in Henderson because the powder coating fails, the steel rusts, and the bracket no longer holds the spring under load.
When the bracket fails, the spring can whip free. That’s a genuine safety risk. Our repair includes new brackets and hardware when the old ones show rust or deformation.
Gate Operator Keypad
Gate Operator Keypad is the control keypad integrated with or wired directly to the operator itself, often used for service access, programming, or a secondary entry point at the motor housing. This is different from the pedestal-mounted entry keypad: the operator keypad talks straight to the control board, not through a receiver. When it stops responding, displays garbled characters, or won’t accept programming changes, it’s usually a ribbon cable, a failed membrane switch, or a control board fault. Replacing a gate operator keypad on a LiftMaster, FAAC, BFT, or Linear unit in Henderson runs $140 to $320 installed. Carver Gate Repair Henderson opens the operator housing, confirms the actual component failure, and quotes the repair before replacing anything.
Programming and Access Codes
The operator keypad is also where some systems let you set master codes, install a new opener, or reset limits. If you inherited an older system with no documentation, you may be locked out of the operator entirely.
We keep factory default procedures and diagnostic manuals for the nine brands we service, so we can reset and reprogram a stubborn FAAC or BFT board without shotgunning parts at the problem. You get a written price for the diagnosis before we start that work.
Weather and Dust Protection
Henderson’s fine desert dust gets everywhere. It works into keypad membranes and under buttons, and once it’s inside, pressing a key feels mushy or fails to register.
We clean and re-seal operator keypads where possible, and if the keypad is too far gone, we swap in a new sealed unit. A fresh gasket and a bead of dielectric grease at the connector extend the life through monsoon season.
Gate Operator Repair
Gate Operator Repair is the full-spectrum fix for the motor, control board, limit switches, safety loops, and wiring that make an automatic gate work. A gate operator that won’t open, reverses direction, beeps constantly, or trips a breaker in your Henderson panel usually has a specific, findable cause. We find it. Carver Gate Repair Henderson tests the power supply first, then the board, then the limit circuit, then the mechanical drive, in that order, because that’s the fastest path to the fault. Most operator repairs in Henderson run $195 to $750 for component-level fixes like control boards, limit switches, and loop detectors. Full operator replacements run $950 to $3,200 for the unit plus installation, depending on whether it’s a swing arm, a slide, or an underground operator.
Limit Switch and Travel Problems
The limit switch tells the operator where the gate stops in both directions. When limits drift, the gate over-travels, bangs the stop, or reverses immediately because the board thinks it hit an obstruction.
We re-set travel limits on FAAC, LiftMaster, and BFT operators, then run the gate through five open-close cycles under load to confirm the settings hold. The fix is often simple, but finding a drifted limit without a service manual is not.
Control Board and Loop Detector Failures
Board failures follow a pattern in Henderson: capacitor swelling from heat, solder joint cracks from years of thermal cycling, and lightning damage during monsoon storms. Loop detectors fail when the saw cut in the driveway fills with dirt or the loop wire gets nicked by tree roots.
We keep control boards and loop detectors in stock for common LiftMaster, Linear, and DoorKing operators, which means many repairs finish in one visit. If your board isn’t in the truck, we order it and give you a firm arrival date before we leave.
Brands We Service
Carver Gate Repair Henderson carries parts and service knowledge for LiftMaster, FAAC, BFT, and Linear, plus five more gate-motor brands: Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. LiftMaster operators are the most common in Henderson’s HOA communities and newer subdivisions, so we stock their control boards, limit switch kits, and remotes on the truck. When a LiftMaster unit fails, we can usually have the part matched and the repair scheduled within the same visit.
FAAC and BFT are common on European-style swing gates and commercial properties, and they demand different programming and hydraulic service than their American counterparts. Linear operators show up frequently on older Henderson homes built before the 2010 changeover to newer LiftMaster equipment. Whether you have one of those brands or any other make, we can help: the diagnostic process is the same, and the written price means you’ll never get a surprise invoice.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- The gate opens halfway and stops. This typically means a limit switch failure, an obstruction-sensor fault, or a failing capacitor that can’t supply enough current for a full cycle. Leaving it half-open means anyone can walk or drive onto your property.
- The motor hums but the gate doesn’t move. A seized gearbox, broken drive chain, or a failed start capacitor. Running it repeatedly in this state can burn out the motor windings and turn a $300 repair into a $2,000 replacement.
- The gate slams or drifts. A lost or broken gate closer spring, or an operator brake that’s no longer holding. A slamming gate is a direct injury risk to children, pets, and anyone standing near the hinge line.
- The breaker trips every time the gate runs. A short in the motor, a failed control board drawing too much current, or water inside the operator housing. Repeated breaker trips can damage your home’s electrical panel beyond the gate circuit.
- The remote works only sometimes. Interference, antenna damage, or a failing receiver module inside the operator. Intermittent operation means you never know when the gate will actually open, which is exactly the kind of unpredictability a gate is supposed to eliminate.
Our Process, Step by Step
- 1
Call or schedule online. A live person answers at (775) 307-6571, any hour, every day. We take your address, the gate type, and a quick description of the problem, then set an arrival window. No answering service, no call-back queue.
- 2
On-site diagnostic. Our technician arrives in uniform, shows identification, and walks the gate with you. We test the power supply, the control board, the limits, the safety edges, and the mechanical drive. If the operator has a fault log, we pull it and read the stored error codes.
- 3
Written quote, approved before work. We write down the problem, the fix, the parts, and the price. That number doesn’t change when the housing comes off. If we find a second problem inside, we stop, show you the issue, and write a new quote. No work happens without your sign-off.
- 4
The repair itself. Parts come from our stock or from a same-day supplier in the Las Vegas valley. We use OEM or equivalent parts matched to your operator’s make and model. The worksite is left clean: no wire clippings, no packaging, no grease on the walkway.
- 5
Testing and the written guarantee. We run the gate through repeated cycles under load, test the safety reversal, and confirm the remotes and keypads work. Then we hand you the written guarantee: 365 days, transferable to the next owner, with a free second visit if the repair fails inside the window.
How Much Does Gate Motor Repair Cost in Henderson?
A typical Gate Motor Repair - North Las Vegas or Henderson service runs $180 to $750, depending on what failed. Limit switch adjustments and capacitor replacements land at the lower end. Control board replacements and loop detector rewiring run $300 to $650. A full gate operator replacement, where the motor and drive unit are swapped out, runs $950 to $3,200 installed, with underground operators at the top of that range because of the excavation and housing work involved. Remote and keypad additions run $85 to $420 depending on the component and whether new wiring is needed.
Three things move the price: the operator brand, the gate type, and the failure point. A swing-arm operator costs less to replace than a slide operator, and a slide operator costs less than an underground unit. The operator’s age also matters: if the board is obsolete, the only option may be a full retrofit. To avoid overpaying, get the diagnosis before you approve anything, ask for the written quote in hand, and don’t let anyone install used electronics. Our estimates are free and include the diagnosis, the recommended fix, and the exact price.
Our Service Area Near Henderson
Carver Gate Repair Henderson serves the entire city plus the surrounding valley, including Enterprise, Spring Valley, Green Valley, Anthem, Whitney, Paradise, Sunrise Manor, Winchester, Southern Highlands, Boulder City, and Nellis AFB. Most Henderson calls can be scheduled same-day or next-morning. We’re also the go-to gate crew for properties near the east side and along the 215 corridor, where many of the larger custom gates are concentrated.
Serving Henderson, NV - Our Local Coverage Area
We’re based in the Henderson area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Motor Repair in Henderson
Gate Motor Repair in Boulder City and Henderson covers the diagnosis and correction of failures in the powered operator that opens and closes an automatic gate. It includes electrical testing, limit switch setting, control board replacement, capacitor swaps, gearbox service, and full operator replacement. In Henderson, it also means dealing with heat-related component failures that shorten motor and board life. Carver Gate Repair Henderson fixes the component that failed rather than replacing the entire operator unless replacement is actually necessary.
Most single-component repairs in Henderson and Gate Motor Repair in Nellis AFB take 45 minutes to two and a half hours on site. A limit switch adjustment usually finishes in under an hour, while a control board replacement plus reprogramming runs closer to two hours. If we don’t have the part on the truck, we order it and return on a scheduled day, typically within two to four business days. Full operator replacements run half a day or more depending on the gate type and whether new conduit work is required.
In Henderson, most gate motor repairs cost between $180 and $750 for component-level work like boards, capacitors, limit switches, and loop detectors. Full operator replacements run $950 to $3,200 installed. Remotes, keypads, and springs land between $85 and $600 depending on the part and the installation complexity. You’ll get a written price before any work starts, so the final invoice matches the quote. Call (775) 307-6571 for an exact quote, estimates are free.
Yes. LiftMaster is the most common gate motor brand in Henderson, and our technicians service LiftMaster swing and slide operators daily. We stock LiftMaster control boards, limit switches, remotes, and capacitors on our service vehicles, which means many LiftMaster repairs finish in a single visit. We also service FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule equipment.
In most Henderson neighborhoods, yes. We hold same-day availability for emergency repairs, particularly when a gate is stuck open or won’t close, because an open gate is a security issue. Calls received before early afternoon usually get same-day dispatch. Call (775) 307-6571 and a live person will tell you the soonest available window, even if it’s a weekend or holiday.
Every repair from Carver Gate Repair Henderson carries the 365-Day Done Right Promise: a written guarantee good for one full year from the date of service. If the repair fails inside that window, we come back and make it right at no charge. The guarantee covers the parts installed and the labor, and it transfers to the next homeowner if you sell the property during the coverage period.
Clear the area around the gate track, the hinge posts, and the operator housing so the technician can access the equipment without moving your property. Have the remote and any keypad codes available for testing. If the operator is inside a locked housing, have the key or combination ready. And if the gate is currently stuck open, keep pets and children away from the gate’s travel path until we finish.
Schedule Your Gate Motor Repair Service in Henderson Today
Call (775) 307-6571 and a live person answers, any hour, any day. Lonnie Burke and the Carver Gate Repair Henderson crew show up on time, in uniform, with the parts and the written quote in hand. The estimate is free, the price is fixed before we start, and the repair is guaranteed for a full year. If you’re in Henderson, Green Valley, Anthem, or anywhere in the valley, we’ll get your gate moving again.
Written by Lonnie Burke, Owner at Carver Gate Repair Henderson, serving Henderson since 2008.