A Carver company - serving Henderson, NV

Before & After Gallery - Carver Gate Repair Henderson

Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Gate Repair Before & After in Henderson, NV

Photos tell the truth faster than any pitch. What follows are real gate repair scenarios we’ve handled across Henderson, from Green Valley to Anthem to MacDonald Ranch. Same gate, same hinge post, same driveway. The only thing changed is the work. We show these because the before shot is usually why you called us, and the after shot is what a repair should look like when it’s actually finished.

Call (775) 307-6571

Explore

Styles & brands we work with

Recent Transformations

Sagging Driveway Gate Realigned in Green Valley

Before: Gate dragging on the driveway, hinge post leaning inward.

After — Before: Gate dragging on the driveway, hinge post leaning inward.

The hinge post had shifted in the caliche soil Green Valley is known for, and the gate was carving a groove into the concrete. We pulled the gate, reset the post in new footing, and replaced the worn hinge bearings. It now clears the driveway by a consistent two inches across the full swing. The written guarantee covers that repair for a full year.

Dead Swing Gate Motor Replaced in Anthem

Technician performing metal gate latch installation and repair — After: New FAAC operator mounted, limit switches set, gate cycling on command.

The homeowner could hear the operator trying, but the arm never moved. We traced it to a failed gear inside the FAAC unit, not the board, which saved replacing the whole system. A new operator went in, the limit switch travel was set, and the gate now opens and closes on every remote and keypad command. No partial swings, no fault codes.

Bent Slide Gate Track Straightened in MacDonald Ranch

Professional welder performing iron gate repair and metal fabrication services — Before: Wheel truck jumping the track, gate binding mid-travel.

Professional gate repair technician applying epoxy to a cracked metal post cap — After: Track straight, wheel trucks rolling clean, gate traveling full length.

A delivery truck clipped the gate a few months back, and it had been getting worse every week. The track had a visible kink, and the wheel trucks were chewing themselves up trying to ride over it. We cut out the bent section, welded in a new rail piece, and replaced both wheel trucks. The gate rolls the full length of its travel without that grinding stop halfway.

Broken Ornamental Gate Pickets Repaired in Seven Hills

Two professionals installing a custom wrought iron gate with power tools — Before: Pickets snapped at the bottom rail, gap wide enough for a small animal.

A professional technician performing expert wrought iron gate installation. — After: New pickets welded in, ground flush, powder coat matched.

Rust had eaten through the base of three pickets, and one good shove would have opened a gap. We cut the rotted sections, welded in matching replacement pickets, and touched up the finish. Unless you knew exactly where to look, you cannot see the repair. The gate is solid again, and the gap is gone.

Loop Detector Fault Fixed on an Estate Gate in MacDonald Highlands

Two contractors installing a custom metal gate between brick pillars. — Before: Gate is standing open and ignoring the close command entirely.

Technician performing professional automatic gate motor repair and maintenance — After: Loop detector reprogrammed, gate closes on its own and holds.

The gate would open, then just sit there. The loop detector in the driveway was reading a phantom vehicle on every cycle, so the safety logic held the gate open. We tested the loop, found the frequency drift, and reprogrammed the detector to the correct sensitivity. The gate now closes automatically and waits for a real car to trigger the loop before opening again.

Failing Hinge Weld Rebuilt on a Commercial Gate Near Lake Las Vegas

Technician performing professional gate motor repair services — Before: Hinge weld cracked through, gate cocked sideways on the post.

Technician performing professional automatic gate motor repair services — After: Hinge rebuilt, gusseted, gate square on its post again.

This gate saw heavy daily use, and the hinge had finally cracked at the weld. We removed the gate, ground out the old weld, and rebuilt the hinge with a gusset plate so it would not fail in the same spot. The gate hangs square and swings without that drop you feel when the barrel is worn. Written price before work started, written guarantee after.

Want Results Like These?

If your gate looks more like the before photos than the after photos, call us at (775) 307-6571. We’ll come to your place anywhere in Henderson, deliver a written price before any work starts, and stand behind the repair with a 365-day guarantee in writing. No invoice surprises, no half-finished work. Just a gate that opens and closes every time.

Written by Lonnie Burke, Owner at Carver Gate Repair Henderson, serving Henderson since 2008.

Before & after

See the difference