FAAC Gate Motor Repair Nationwide

FAAC Gate Motor Repair in Henderson: What to Know First

FAAC gate motor repair in Henderson typically runs $225 to $480 for most control board, limit switch, and capacitor failures, with a written price agreed before we open the housing. Most FAAC repairs in Henderson finish the same day the parts are on the truck, which covers roughly 80 percent of what we see. If your motor needs a full replacement, you’re looking at $900 to $2,100 installed, depending on the model and whether we reuse your existing gate hardware.

Call (775) 307-6571

This page is for Henderson homeowners with a FAAC swing or slide gate operator that stopped responding, started running rough, or quit mid-cycle. If that’s you, call (775) 307-6571 and describe what the gate is doing. Lonnie Burke and our crew work on FAAC equipment across Henderson weekly, from Green Valley Ranch to Anthem. We’re an independent FAAC service provider, not a factory shop, which means we diagnose before we sell parts.

How FAAC Products Fail – and How We Fix Them

FAAC builds solid operators, but every line has its patterns. Here’s what we actually find when we open a FAAC motor in Henderson:

• FAAC 400 and 412 swing operators: capacitor failure after 5 to 7 years. The symptom is a gate that hums but won’t start, or starts slow and labors. The capacitor sits in a housing that traps heat, and Henderson summers push it past its rated life. We replace it with an OEM-spec unit, not a generic, and we check the start winding at the same time so you don’t get a call-back in three months.
• FAAC 750 and 844 slide operators: limit switch drift. The gate stops short of full open, or over-runs the closed position. On FAAC slide models, the limit cams wear where the follower rides them, and the gate loses its stops by inches. We reset and replace the switch assembly, then run the gate through ten full cycles to confirm the stops hold.
• FAAC E024U control boards: relay failure from power surges. Henderson gets more brownouts than people realize, especially near the foothills when summer storms roll through. The relay that drives the motor contacts burns out, and the board looks dead when it isn’t. We test the board before condemning it. A board replacement is the most common FAAC repair we do that could’ve been a $40 fix if someone had checked the relay first.
• FAAC 770 hydraulic operators: low fluid or a blown seal. These are quieter than the electromechanical models, but they leak eventually. The gate slows down, especially in cold weather when the fluid thickens. We top off the correct hydraulic fluid and replace seals, then cycle the gate under load to confirm pressure holds.
• FAAC photo eye and loop detector faults: wiring degradation at the gate post. The operator’s fine. The gate just stops and reverses, or won’t close at all, because the safety circuit is seeing ghosts. The photo eye wiring entering the post gets baked by the sun and cracked, and Henderson dust gets into the housings. We trace the circuit, replace the damaged section, and re-align the eyes so the gate doesn’t act like it’s possessed.

Our FAAC Gate Motor Repair Process

Here’s what a FAAC repair looks like when you call Carver Gate Repair Henderson:

1. 1
   You call and talk to a person. Our phone is answered live, 24/7. We ask what the gate is doing, when it started, and which FAAC model you have. That tells us what parts to bring.
2. 2
   We give you a written price before we touch anything. The diagnostic happens first, then we hand you a number. That number doesn’t move when the housing comes off.
3. 3
   We open the operator and test the parts, not guess. Capacitor, limit switch, relay, board, wiring. We test before we replace. Lonnie’s rule: tell me what it’s doing wrong, and I’ll tell you what it needs, usually those are two different things.
4. 4
   The repair. OEM FAAC parts when the job calls for them, quality aftermarket when it’s a better value and won’t affect function. We use what’s right for the repair, not what’s easiest to bill.
5. 5
   We run the gate through full cycles under load. Open, close, obstruction test, safety edge check, photo eye alignment. If it doesn’t behave, we’re not done.
6. 6
   You get the guarantee in writing. Every repair carries a 365-day written guarantee. If it fails inside the year, we come back and fix it at no charge.

What FAAC Gate Motor Repair Costs in Henderson

Here’s what FAAC owners in Henderson should expect:

• Capacitor replacement: $145 to $260
• Limit switch repair or replacement: $180 to $320
• Control board repair or replacement: $350 to $690
• Photo eye or loop detector repair: $160 to $340
• Full operator replacement (FAAC swing or slide): $900 to $2,100 installed

What moves the price is the model, the part, and how much of the job is repair versus replacement. A 400-series swing motor is a different job than a 750 slide operator. The written quote you get before we start covers the full scope, so there’s no surprise line item at the end. Call (775) 307-6571 for a free estimate on your specific FAAC setup.

Why Henderson Homeowners Call Carver Gate Repair Henderson for FAAC Work

Because a gate that won’t close is a security problem, and we treat it that way. We dispatch background-checked, uniformed technicians. We answer the phone around the clock. And we put the guarantee in writing, for a full year, on every FAAC repair we do in Henderson.

We’re also not a one-brand shop. When a FAAC operator is beyond repair and the right move is a switch, we install LiftMaster, Mighty Mule, Ghost Controls, and DoorKing systems too. That matters because you get an honest recommendation. If your FAAC still has years in it, we’ll tell you. If it doesn’t, we’ll tell you that too, and give you a written price on whatever replaces it.

FAQs