FAAC Hinge & Roller Replacement Nationwide

FAAC Hinge & Roller Replacement: The Henderson Owner’s Guide

FAAC hinge and roller replacement in Henderson typically runs $150 to $420 installed, depending on the gate weight, hinge style, and whether the roller assembly is seized or just worn. We stock FAAC-compatible hinges and rollers on the truck and can usually complete the swap in under two hours on the first visit. Most Henderson homeowners discover the problem the same way: the gate starts dragging on the ground, binds halfway through its swing, or makes a groaning sound that gets worse every week.

Call (775) 307-6571

What you’re hearing is metal fatigue and wear. The hinge takes the gate’s full weight every time it swings, and the roller carries it along the track. In Henderson’s heat, the grease inside those rollers breaks down fast, and once it’s gone, the bearing runs dry until it seizes or the wheel flattens on one side. We replace both the hinge and roller so the gate hangs true again and the operator isn’t fighting a part that’s already half-dead.

Key Takeaways:

• Installed cost for FAAC hinge and roller replacement in Henderson: $150 to $420.
• We carry FAAC-spec hinges and rollers on the truck, plus quality aftermarket equivalents that match the original dimensions.
• Most replacements are done same-visit; we write the price down before turning a single bolt.
• Every repair carries the 365-Day Done Right Promise in writing.

Which FAAC Models This Applies To

This part applies to most FAAC swing gate systems still running in Henderson: the 400 series operators (402, 412, 415, 422), the 750 and 760 series, and the older 390/391 setups we still see on custom gates out toward Anthem and the Raiders practice corridor. The hinge and roller aren’t proprietary magic: they’re engineered to FAAC’s spec, but the dimensions matter. Gate weight, leaf width, and post configuration determine which hinge and roller set fits without grinding or premature wear.

The model plate on the operator tells you the operator model, but the hinge spec is set by the gate itself. That’s the gotcha. A FAAC 412 running a 12-foot steel leaf needs a heavier hinge and roller than a 412 on a 6-foot ornamental gate. We measure the leaf, check the current hinge spacing, and match the replacement to the load. If your existing hinge was mis-specified by a previous installer, we’ll tell you and quote the correct part instead of copying the mistake.

On OEM versus aftermarket: FAAC-branded hinges and rollers are solid, but the aftermarket equivalents from BFT and DoorKing suppliers can be equal or better for less money, provided the pin diameter, leaf thickness, and roller wheel material match. We stock both and quote them separately, so you can see the difference in writing. Carver Gate Repair Henderson is an independent service provider, not affiliated with FAAC, and we match parts to the gate, not to a brand label.

Lonnie Burke has been matching FAAC parts long enough to know that half the trouble is someone installing a light-duty hinge on a ranch gate and hoping for the best. “Tell me what it’s doing wrong, and I’ll tell you what it needs – usually those are two different things.” That’s how we start every FAAC hinge and roller job in Henderson: measure first, then quote, then touch the gate.

Signs Your FAAC Hinge & Roller Replacement Is Failing

• The gate drags at the latch side. The hinge pin has worn or the bushing has egged out, dropping the far end of the leaf. If you can lift the gate an inch at the open end, the hinge is done.
• The gate shudders mid-swing. A flat-spotted roller wheel hits the track like a square tire, jerking the leaf every revolution. In Henderson, the heat hardens those wheels and then the sun bakes the flat spot permanent.
• A groaning or squealing noise that gets worse each week. The roller bearing has run dry and is grinding itself into iron dust. Once it starts screaming, the shaft is usually scored beyond saving.
• The operator trips its safety sensor and reverses. The motor is drawing high amps because the hinge is binding and the roller is dragging. The opener thinks it’s hitting something. It’s not – it’s just trying to move a gate that’s fighting it.
• Visible rust streaks from the hinge pin or roller axle. Water intrusion has killed the lubricant and started oxidizing the steel. Henderson’s dry air slows it, but sprinkler overspray and monsoon-season humidity accelerate it in ways we see all the time.

Replacement Cost & What’s Included

In Henderson, a FAAC hinge and roller replacement runs from $150 to $420 installed. The spread is driven by three things: how heavy the gate leaf is, whether we’re swapping one hinge or both, and whether the replacement is a drop-in match or requires drilling new mount holes. A single light-duty hinge with a roller on a 6-foot ornamental gate sits at the low end. A heavy steel ranch gate needing both hinges, new rollers, and re-hung leaf alignment lands at the upper end.

Every quote is written, and we hand it to you before we start. That number includes the parts, the labor to remove the old hinge and roller, the install, and the adjustment so the gate hangs and rolls true. It does not include surprises, because there are none. If we find damage beyond the hinge and roller while we’re in there – a cracked post or a bent leaf – we stop and quote it separately before doing anything else.

The work is covered by the 365-Day Done Right Promise, written on every repair, good for a full year from the service date. If the hinge or roller fails inside that window, the second visit is free. No charge, no argument.

DIY or Call Us?

You can safely check a few things without tools: lift the gate at the open end to feel for play, watch the roller as the gate swings to see if it’s turning or sliding, and look for rust dust around the hinge pin. That tells you what’s wrong. It won’t tell you the correct replacement spec, and that’s where DIY goes sideways.

The hinge carries the full weight of the gate. A mis-sized replacement or a poorly seated pin puts a falling gate in play – and a falling iron gate will hurt someone. The roller has to match the track profile and ride height, or the gate binds and burns out the operator. We’ve fixed enough owner-installed replacements in Henderson to know that a $40 online hinge turns into a $600 repair when the wrong part throws the alignment and kills the motor. If you want to save the diagnosis, go measure and call us with the numbers. If you want it fixed, call (775) 307-6571 and we’ll come do it right.

FAQs