Linear Hinge & Roller Replacement Nationwide

Linear Hinge & Roller Replacement: The Henderson Owner’s Guide

We stock and install Linear-compatible hinges and rollers for most residential gate systems, with typical hinge and roller replacement running between $185 and $420 installed in Henderson depending on the gate’s weight and how many components need swapping. Most calls come in when a gate starts dragging on the ground, squealing when it moves, or leaning hard against one post. The roller or hinge has usually been wearing quietly for months before anyone notices, and by the time the gate sags enough to scrape concrete, at least one roller is flat-spotted and one hinge pin is ovaled out.

Call (775) 307-6571

Linear built a lot of the swing and slide gate hardware you still see across Henderson neighborhoods, and the good news is that hinges and rollers are standard wear items, not exotic parts. You do not need a new motor because a roller failed. You need the right replacement roller, matched to the track and gate weight, and a hinge that hasn’t been bent by a wind gust off the McCullough Range. That’s the job we show up for most weeks.

Which Linear Models This Applies To

Linear hinges and rollers appear across the brand’s residential gate lines. On the swing side, you’ll see them on Linear’s standard-duty swing gate hardware paired with operators like the Linear LRA series. On slide gates, Linear’s track hardware runs under heavy gates on both the SL and SW lines, and those rollers sit in a channel that collects caliche dust faster than you’d expect in Henderson. The hinge-and-roller work is the same type of repair whether the opener is a Linear, a LiftMaster, or a Mighty Mule, because the mechanical half is what wears.

Here’s the compatibility gotcha most owners miss: roller diameter is not a suggestion. Slide gate rollers come in sizes matched to the track, commonly 3-inch, 4-inch, and 6-inch diameters, and a roller that’s too small lets the gate ride low and chew the track. A roller that’s too wide binds on the channel walls. Linear’s residential slide hardware generally uses 4-inch rollers for standard gates, but we measure before we order anything, because field conditions in Henderson vary. Wind, heat, and gate weight all bend what was once straight.

On hinges, the choice is OEM Linear or a quality aftermarket equivalent in stainless or galvanized steel. Linear’s OEM hinges are solid, but for heavy gates, an aftermarket bearing hinge often outlasts the factory bushing hinge. We carry both and will tell you honestly which one makes sense for your gate weight, not for our margin.

Signs Your Linear Hinge & Roller Replacement Is Failing

• The gate drags or scrapes the ground on one end. This is the classic failing-roller symptom. The wheel has worn flat on one side, so instead of rolling it slides, and the gate drops low enough to shave concrete.
• A grinding or squealing noise when the gate moves. Roller bearings go dry, then they heat up, then they disintegrate. A squeal is the bearing telling you it’s been running without grease for a long time. By the time it grinds, the wheel usually has flat spots.
• The gate leans visibly toward the latch post or the hinge post. A worn hinge pin lets the gate drop at the free end. On wide gates, half an inch of pin wear becomes several inches of sag at the far end.
• The gate moves stiffly or sticks mid-travel. A collapsed roller or a seized hinge forces the motor to work harder. That extra strain shortens the operator’s life, and the gate will sit half-open until you shove it.
• The gate sits lower on one side than the other while closed. Measure the gap under the gate at both ends. If one side is noticeably tighter to the ground, a hinge or a roller is gone, even if it still moves without noise.

Replacement Cost & What’s Included

In Henderson, hinge and roller replacement on a Linear-equipped gate typically lands between $185 and $420 installed. The range is driven by three things: how many rollers or hinges are being replaced, the gate’s weight and length, and whether the track itself needs work because a flat roller chewed it up before you caught the problem. A single roller swap on a light driveway gate sits at the bottom of that range. Both hinges and two rollers on a long slide gate sit at the top.

Every price is written before the work starts. No estimate that grows once the gate is apart. The price includes the parts, the labor, removal of the old hardware, and a written guarantee on the repair that lasts a full year from the date of service. If the repair fails inside that window, the second visit is free, no charge, no argument. That’s the Garrison Standard, and it applies to every job we run in Henderson, regardless of which crew member shows up.

Call (775) 307-6571 for an exact quote. Estimates are free. We’ll tell you over the phone whether it sounds like a roller, a hinge, or something else entirely before anyone schedules a visit.

DIY or Call Us?

A homeowner can do a few useful checks before picking up the phone. Look at the gate from the street and see if it leans. Put a hand on the gate and try to lift the free end, if it lifts more than a quarter inch, you’ve got a worn hinge or a bad roller. Check whether the rollers turn freely or look squared off. Those checks are safe and they tell us a lot before we arrive.

What we do not recommend is swapping gate rollers or hinges as a DIY project on any gate that’s more than a light single-car walk-through. A fully loaded slide gate can weigh 300 to 800 pounds. If the gate comes off its track while you have hardware removed, that’s a serious injury and a broken gate. The roller hardware also sits under tension in its track, and releasing it the wrong way sends the gate sideways with no control. If the gate is heavy, call us at (775) 307-6571. If the gate is light and you’re determined to try it yourself, at minimum block the gate securely with a jack stand before unbolting anything.

FAQs

Call Carver Gate Repair Henderson

If your Linear gate is dragging, leaning, or grinding, call (775) 307-6571. A live person answers, day or night, every day of the year. We’ll listen to what the gate is doing, tell you what it likely needs, and give you a written price before any work starts. Lonnie Burke and the crew at Carver Gate Repair Henderson have been fixing gate hardware in this valley for years, and we wear the Garrison Standard on every job: written prices, background-checked technicians, and a guarantee in writing that’s good for a full year. Tell us what the gate is doing wrong, and we’ll tell you what it needs. Usually those are two different things.

Written by Lonnie Burke, Owner, Carver Gate Repair Henderson at Carver Gate Repair Henderson, serving Henderson and nearby areas.