Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Boulder City
Gate repair in Boulder City usually runs $150 to $400 for common fixes like hinge work, realignment, and latch replacement, while motor and control board work lands between $350 and $900. Most jobs are completed in a single visit. If you’re in Boulder City with a gate that won’t open, sags on its hinges, or stopped responding to the remote, call (775) 307-6571 and a live person answers, day or night.
We know Boulder City’s gates differently than a generalist contractor would. The housing stock here wasn’t poured from a 1990s subdivision template. Homes along Nevada Way, Georgia Avenue, and the streets branching off Adams Boulevard were built between 1931 and 1945, and many still hang their original wrought iron gates, hand-forged, with no two alike. That changes how a repair should be approached. We dispatch crews who understand what they’re walking up to before they arrive, and we quote a written price before any work starts.
Why Carver Gate Repair Henderson Is Boulder City’s Preferred Gate Repair Company
Boulder City homeowners call us because the person who answers the phone knows what a limit switch does and doesn’t read from a script. Lonnie Burke runs the crew to The Garrison Standard: background-checked technicians, written prices, and a clean job site when the truck leaves. That standard has been in place since 2008, and every Boulder City repair carries the same 365-Day Done Right Promise in writing, good for a full year from the date of service.
We serve Boulder City homes from our Henderson location, with dispatch coordinated through the Las Vegas office. Response to most Boulder City neighborhoods runs within the same day for non-emergency calls, and emergency service is available around the clock. Our Gate Repair team arrives in uniform, identifies themselves, and walks the gate with you before touching a tool. If a repair fails inside the guarantee window, the second visit is free. No charge, no argument.
Homeowners in the Boulder City Historic District have a specific worry: a repair tech who shows up, takes one look at a 1930s iron gate, and says “replace it.” We don’t do that. We match the metal, the twist pattern, and the finish. That’s not marketing language; it’s the only way to work on gates that the city’s preservation review watches closely.
Styles & brands we work with
Sliding Gate Repair in Boulder City
Sliding gate repair in Boulder City typically runs $250 to $650 for mechanical work like rack replacement, roller replacement, and track realignment, while motor and limit switch issues fall between $350 and $900. Slide gates are less common on the historic single-family streets than swing gates, but they show up on larger lots along the edges of town and on a few commercial properties near Boulder City Parkway. When a slide gate binds or grinds, the cause is nearly always the rack, the rollers, or a track fouled with desert grit.
Rack, Roller, and Track Work
The rack is the toothed steel bar mounted along the gate that the motor’s gear drives against. Boulder City’s dry wind pushes fine sand and dust into rack teeth, which accelerates wear and causes the gate to jump or stall mid-travel. We inspect the full rack run, replace worn sections rather than the entire length when it’s sound, and re-align the drive gear so it engages cleanly.
Rollers fail when their bearings seize from grit or when the weight of the gate exceeds what the original spec allowed. We replace rollers in pairs, check the track for flat spots, and set the gate height so it carries weight evenly across all points. A slide gate that drags at one end is a gate that’s about to burn out its motor.
Motor and Limit Switch Service
On motorized slide gates, the limit switch tells the operator when to stop. If the gate slams at full speed or stops six inches short of the post, that’s a limit switch or a control board problem, not a strength problem. We service BFT, Linear, and Viking slide operators regularly in Boulder City, and we stock common control boards and limit switches in the truck rather than ordering and waiting.
Wrought Iron Gate Repair in Boulder City
Wrought iron gate repair in Boulder City typically runs $200 to $500 for hinge replacement, post re-setting, and rust repair, while scrollwork fabrication and custom finial matching can run $400 to $1,200 depending on how much of the gate must be reproduced. The old gates here are genuinely wrought iron, not the hollow mild steel sold at big box stores. That’s good news for longevity and bad news for anyone who thinks a stock replacement panel will match.
Post Re-setting and Hinge Work
The single most common failure we see on Boulder City’s older gates is a hinge post that has moved. Posts set in 1940 were often bedded in shallow concrete, and decades of irrigation water pooling at the base corrodes the steel below ground level. When the post leans, the gate drops and drags. We excavate the footing, re-set the post plumb in fresh concrete, and re-hang the original leaf so it clears the ground the way it did when it was installed.
Rust Repair and Ornamental Matching
Rust on a 1930s iron gate isn’t a reason to replace the gate. We cut out corroded sections, weld in matching bar stock, and grind the joint so it disappears under primer and paint. When a finial is missing from a historic district gate, we fabricate a replacement from solid stock and match the twist pattern of the surviving pieces. You’d have to know which finial was replaced to find it.
Trusted Brands We Service in Boulder City
We work on nine gate motor brands, and Boulder City calls skew toward legacy LiftMaster linear actuators, older BFT swing operators, and a steady run of Ghost Controls and Viking units on newer retrofits. We stock common replacement parts for these systems so most Boulder City repairs don’t wait on a parts shipment from a distributor in another state. Matching the right board to the right operator matters, especially on older units where the original enclosure won’t accept a modern board without an adapter plate or minor fabrication.
Common Gate Repair Problems We See in Boulder City Homes
- Sun-baked photocells on old openers. Boulder City summer heat eventually kills the photo eyes on pre-2000 automatic gates. The gate starts reversing for no reason or refuses to close because the safety circuit is reading a fault. UL 325 requires functioning photocells; we replace them with modern units and wire them correctly.
- Corroded hitch-side hinge posts. The hand-forged posts on 1930s and 1940s gates corrode at grade level where irrigation overspray keeps the base damp. When the post drops a quarter inch, the gate leaf drags across the walk. We re-set posts and replace the lower hinge leaf when the metal is too far gone to save.
- Obsolete control boards that no longer fit. Summer voltage spikes take out control boards on older LiftMaster and linear actuators. The replacement board often doesn’t mount in the original enclosure, so we fabricate adapter brackets rather than telling you to buy a whole new operator.
- Worn latch and strike alignment on swing gates. Gates that were hung before modern automatic operators existed often have vintage latches that no longer line up after years of use and post movement. We adjust or rebuild the latch assembly so the gate closes and holds without slamming.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Boulder City, NV
Here’s what Boulder City homeowners should expect to pay for common gate work. Hinge and latch repair runs $150 to $350. Gate realignment, including post shimming and hinge adjustment, runs $200 to $400. Weld and rust repair runs $250 to $600 depending on how much metal must be cut out and replaced. Electric gate repair, including control board, receiver, and limit switch work, runs $350 to $900. Full motor replacement on an automatic gate runs $800 to $1,800 installed.
- Hinge and latch repair: $150 to $350
- Gate realignment and post adjustment: $200 to $400
- Weld and rust repair: $250 to $600
- Electric and control board repair: $350 to $900
- Full motor replacement: $800 to $1,800
Every price is written down and agreed to before we start. The number doesn’t move at the door. Call (775) 307-6571 for a free estimate on any gate repair in Boulder City, and we’ll give you a straight answer on what the job needs and what it costs.
We Also Serve Cities Near Boulder City
Our crews cover Boulder City and the surrounding area, including Henderson, Nellis AFB, and North Las Vegas. If you’re just outside Boulder City and need gate work, call us and we’ll route the nearest available technician. Response times to the neighboring cities run within the same day for non-emergency calls, and 24-7 emergency service applies throughout the service area.
Serving Boulder City, NV - Our Local Coverage Area
We’re based in the Boulder City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Boulder City
Yes. We repair original ironwork in place using matching bar stock, period-correct hardware, and finishes that blend with the existing gate. The preservation rules in the Boulder City Historic District require restoration rather than replacement, so we fabricate missing finials, rebuild corroded sections, and re-hang the original gate leaves rather than swapping in new panels. The city’s review process accepts repairs that maintain the original material and profile. Call (775) 307-6571 to schedule an assessment.
No. UL 325, the federal safety standard for automatic gate operators, requires functioning photoelectric sensors on all automatic gates, including ones installed decades ago. An operator without photocells is non-compliant and dangerous, especially around children and pets. We can retrofit photo eyes on nearly any older operator, often without replacing the motor, and we hide the wiring so it doesn’t spoil the look of a historic gate. Call us at (775) 307-6571 and we’ll check the system and bring it up to standard.
Boulder City sits at a higher elevation with hotter, drier summers, and the sustained heat plus intense UV exposure ages electronic components faster than in the slightly cooler basin where Henderson sits. Control boards and photocells take the worst of it, and summer voltage spikes during monsoon-fed grid strain add to the failure rate. That’s why we stock common boards for LiftMaster, Linear, and BFT operators so repairs can happen in one trip. For a specific diagnosis, call (775) 307-6571.
If the rack teeth are worn only in the travel zone where the gate spends most of its time, which is common in Boulder City’s abrasive desert grit, you can replace just the worn section for $150 to $350. If the rack is worn across more than half its length or the drive gear is also chewed up, replacing both runs $400 to $800 and is usually the smarter long-term fix. We’ll show you the wear before we quote anything, and the written price won’t change after you approve it. Call (775) 307-6571 for an honest assessment.
Yes. A solar gate opener works well in Boulder City because of the reliable sun, and we install the panel and battery in a way that doesn’t alter the original gate’s appearance. The operator mounts behind the gate leaf, the solar panel goes on a post or a low-profile ground mount, and the vintage hardware stays untouched. We use swing operators from Ghost Controls or Viking depending on gate weight and leaf length. Call (775) 307-6571 for a free measure and a written price.
Contact Carver Gate Repair Henderson for Gate Repair in Boulder City
If your Boulder City gate is sagging, stuck, or refusing to open, call (775) 307-6571 now. A live person answers, any hour, any day. We’ll schedule a visit, send a background-checked technician in uniform, and put a written price in your hand before the first tool comes out of the truck. Every repair carries the 365-Day Done Right Promise, in writing, good for a full year. If the repair fails inside that year, we come back and fix it free.
Written by Lonnie Burke, Owner at Carver Gate Repair Henderson, serving Boulder City under The Garrison Standard since 2008.