Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterElectric Gate Repair in Henderson, NV
Electric gate repair in Henderson typically runs between $180 and $600 depending on what’s failed, with most jobs completed the same day we diagnose the problem. The most common issues we see are dead control boards, stripped drive gears, failed limit switches, and misaligned safety sensors. If your gate won’t open, won’t close, or reverses halfway through its cycle, call Carver Gate Repair Henderson at (775) 307-6571 and a live person will answer, day or night.
We’re not a general handyman service that occasionally touches a gate. Electric gate systems are what we work on every day. Whether your swing operator has stopped responding to the remote or your slide gate grinds and stops, our technicians arrive with the right parts for LiftMaster, FAAC, BFT, and Linear systems already on the truck. If you’re dealing with broader gate problems beyond the electrical side, start with our Gate Repair in Henderson page for the full picture. For everything else, this page covers the electrical work specifically.
When You Need Electric Gate Repair
Electric gates fail in predictable ways, and Henderson’s heat and dust accelerate certain failures. Here are the symptoms that tell you the electrical system needs attention:
- The gate won’t respond to the remote or keypad. This usually points to a failed receiver board, a dead transformer, or a blown fuse in the control box. In Green Valley and Anthem, we see this often after summer monsoons knock out power and surge the board.
- The gate starts moving, then stops and reverses. This is almost always a safety sensor issue, specifically the photo eyes near the gate’s path or a loop detector under the driveway that’s no longer sensing a clear zone. Dust accumulation on sensor lenses is a common culprit in Henderson’s dry climate.
- The gate grinds, struggles, or moves halfway. That’s a mechanical problem fed by an electrical one. The motor is getting power but the drive gear is stripped, or the capacitor that starts the motor has failed. We replace the capacitor or gear rather than selling you a whole new operator when it’s not needed.
- The gate opens but won’t close, or closes but won’t open. A failed limit switch tells the control board the gate is in the wrong position. The board keeps waiting for a signal that never comes. This is a $45 part that takes 20 minutes to replace.
- The battery backup chirps or the keypad screen is blank. Batteries in gate systems last three to five years. When they go, the gate loses its memory and the keypad resets. We swap the battery, reprogram the board, and test the full cycle.
- The gate slams shut instead of slowing near the end of its travel. That’s a bad internal limit or a worn-out arm on a swing operator. Left alone, it damages the hinge and the motor mount.
If you’re noticing any of these, call (775) 307-6571. We’ll ask a few questions, tell you what we think is wrong, and give you a written price before anyone touches the gate.
Our Electric Gate Repair Process
We run every Gate Repair Near Me in Henderson, NV through the same five-step process. It’s part of The Garrison Code, the operating standard that governs how our crew shows up, works, and leaves. Nothing here is optional.
- You call, a person answers. Not a voicemail box. Not a callback queue. A live dispatcher answers (775) 307-6571 and schedules your visit. We’ll tell you the arrival window before we hang up.
- Technician arrives, diagnoses, and writes the price. The technician is background-checked and in uniform. They test the control board, power supply, sensors, and operator. Then they write down the price for the repair before any work starts. That number doesn’t move at the door.
- Repair work with the right parts. We carry boards, gears, limit switches, capacitors, sensors, and remotes for LiftMaster, FAAC, BFT, and Linear systems on the truck. That means most Henderson repairs are done same visit.
- Full cycle testing and safety verification. After the repair, we run the gate through at least five full open and close cycles. We test the safety sensors, the auto-reverse function, and the manual release. If it doesn’t pass, we don’t leave.
- Written guarantee and a clean site. Every repair carries our 365-Day Done Right Promise in writing. If the same repair fails within a year, the second visit is free. We sweep up, put tools away, and walk you through what was fixed.
Electric Gate Repair Pricing in Henderson
You should know How Much Does Gate Repair Cost? (2026 Price Guide) - Henderson, NV before you pick up the phone. Here are the ranges we typically see across the valley:
| Repair Type | Typical Cost Range in Henderson |
|---|---|
| Diagnostic visit (credited toward repair if you proceed) | $59 – $89 |
| Limit switch replacement | $120 – $220 |
| Safety sensor or photo eye replacement | $130 – $250 |
| Control board replacement | $280 – $600 |
| Drive gear or sprocket replacement | $180 – $380 |
| Capacitor or transformer replacement | $110 – $190 |
| Complete swing or slide operator replacement | $900 – $2,200 |
Several things move the Gate Realignment price. The brand of the operator matters because parts cost differs. The age of the system matters too: a 20-year-old board that’s no longer manufactured may require a retrofit kit. And the type of gate, swing or slide, determines how much labor is involved. What doesn’t move the price is us once we quote it. The written price you get before work starts is the price on the invoice. If the repair falls under our guarantee, a return visit costs you nothing for the same issue.
We don’t charge for an estimate. Call (775) 307-6571, tell us what the gate is doing, and we’ll give you a realistic range over the phone before we even schedule.
FAQs – Electric Gate Repair
How much does electric gate repair cost in Henderson?
Electric gate repair in Henderson typically costs $180 to $600, with small fixes like limit switches starting around $120 and full control board replacements reaching $600. Complete operator replacement runs $900 to $2,200 depending on the system. Call (775) 307-6571 for a written quote and we’ll give you an exact number, not a range.
Can you fix my electric gate today?
Yes. We keep same-day appointments for Henderson gate repairs, and our phone line is answered by a live person 24/7. Most electric gate repairs we complete in one visit because the technician arrives with the common failure parts already on the truck. Call (775) 307-6571 to get a time window today.
Is it cheaper to repair or replace my electric gate operator?
Repair is cheaper when the failure is a single component, like a limit switch, capacitor, or gear. Replacement makes more sense when the operator is over 15 years old, the board has failed, and the motor is drawing excessive current. We’ll tell you honestly which path costs less over the next five years.
What does your guarantee cover?
Our 365-Day Done Right Promise covers every electric gate repair in writing for a full year from the date of service. If the same repair fails within that window, we come back and fix it free of charge. The guarantee is part of The Garrison Standard, not an upsell.
If your gate won’t move, won’t stop, or won’t stay closed, call our team at (775) 307-6571. We’ll answer, ask the right questions, and get a uniformed technician to your Henderson home with a written price before the work starts.
Written by Lonnie Burke, Owner at Carver Gate Repair Henderson, serving Henderson.