Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Henderson Homeowners
A gate that won’t open or close leaves your family waiting in the driveway, or worse, leaves your property unsecured overnight. Our Automatic Gate Repair team responds fast. In Henderson, where summer heat bakes motor housings and winter winds stress hinges and weld points, gate failures don’t fix themselves. Carver Gate Repair Henderson handles gate repair across Henderson, Green Valley, Anthem, and Whitney with background-checked, uniformed technicians and a written price before any work starts. We operate to The Garrison Standard, which means every repair carries a written guarantee good for a full year. Call (775) 307-6571 and a live person answers, 24/7, including weekends and holidays. Lonnie Burke leads the Carver team in Henderson with the same discipline that has defined the Garrison Partners family since 2008.
Driveway Gate Repair
Electric Gate Repair covers the gate itself plus the operator that moves it: hinges, wheels, track, chain, belt, circuit board, and safety sensors. You need it when the gate drags, binds, reverses mid-cycle, or stops responding to the remote. Carver Gate Repair Henderson evaluates the whole system before touching a screw, so you know whether the fix is a $95 sensor alignment or a $600 circuit board replacement before you commit. We don’t open the panel and surprise you with a number later.
Operator Diagnosis
Most driveway failures start at the motor or its control board, not the physical gate. We bench-test the board, check capacitor draw, and verify limit switch logic before replacing parts. The written quote lists each component and its cost.
Gate Alignment and Track Correction
A gate that scrapes or shudders is usually fighting its own track and needs Gate Realignment. We true the track, reset wheel spacing, and re-hang drooping gate leaves so the motor isn’t pushing against resistance that shortens its life.
Styles & brands we work with
Gate Welding
Gate welding joins broken metal so a damaged gate becomes structurally sound again, not just patched. You need it after an impact, or when rust has eaten through a bottom rail or hinge post. Carver Gate Repair Henderson welds steel and aluminum gate frames in place or in our shop, grinds the repair smooth, and repaints or coats it to match. A broken weld at a hinge point can drop an entire gate leaf, so we don’t treat this as cosmetic work. Typical structural welds run $180 to $450 depending on the size of the break and whether the gate must be removed.
Hinge and Post Repairs
When a weld fails at the hinge, the gate’s weight shifts and every other component starts wearing faster. Our Hinge & Post Repair fixes this before it spreads. We cut out the failed section, weld in fresh material, and reinforce the post if it has twisted.
On-Site Frame Reinforcement
Some repairs demand a hotter weld or a bench fixture, but many frame cracks can be repaired at the property. We bring mobile welding gear to Henderson homes when the repair is clean and accessible.
Commercial Gate Repair
Commercial gate repair keeps apartment, warehouse, and industrial gates cycling reliably every time a tenant or truck approaches. Downtime matters more here, because access control failures stall deliveries and create liability. Carver Gate Repair Henderson services sliding and swing gates at commercial properties across Henderson, including the Green Valley business corridors. We carry commercial-grade parts for LiftMaster and BFT operators and handle vehicle loop detectors, keypad and intercom interlocks, and high-cycle hardware replacements that residential crews aren’t equipped for. Expect commercial repairs to start around $300 and scale with the system’s complexity.
Vehicle Detection and Loops
When a gate won’t open for a car but opens for the remote, the loop detector is usually dead. We test loop continuity, replace sawcut loops where necessary, and calibrate the detector so oversized trucks don’t trigger false opens.
High-Cycle Hardware
Commercial gates run 200 to 500 cycles a day, and residential parts fail quickly under that load. We spec wheels, rollers, and hinges built for that duty cycle so you’re not paying for the same repair in eight months.
Iron Gate Repair
Iron gate repair addresses rust, failed joints, bent pickets, and corroded fasteners on ornamental iron gates common throughout Henderson’s Anthem and MacDonald Ranch neighborhoods. Iron is heavy and unforgiving: a sagging iron gate grinds down its own hinges and eventually pulls the post out of plumb. Carver Gate Repair Henderson straightens bent members, replaces rotten fasteners with stainless, and welds cracked intersections before they spread. Repairs on iron gates typically run $150 to $600 depending on the extent of rust damage and whether the gate must be removed for a proper repair. Leaving rust untreated in Henderson’s dry climate still allows corrosion, just slower, so we treat every repair site with rust converter and paint or cold-galv coating matched to the original finish.
Rust Treatment and Prevention
Surface rust is a warning, not a death sentence. We grind the affected area, treat with rust converter, and seal it so moisture can’t restart the cycle. Full restoration falls under our Gate Repair in Henderson work when more than 30 percent of the metal is compromised.
Picket and Scroll Straightening
Bent pickets and broken scrolls compromise the gate’s look and its geometry. We straighten what can be saved and weld replacement sections where the metal has fatigued.
Sliding Gate Repair
Sliding gate repair fixes cantilever and track-style sliding gates that bind, jump the track, or won’t reach the close limit. These gates depend on rollers and a guide system, and when those wear, the motor strains and eventually fails. Carver Gate Repair Henderson works on sliding driveway and commercial gates across Henderson and Whitney, replacing nylon and steel rollers, repairing chain drives, and resetting the rack. A sliding gate repair typically runs $200 to $500 before any replacement operator parts, and we quote the full number in writing before work starts.
Roller and Truck Replacement
Worn rollers cause the gate to drag and the operator to pull excessive amperage. We match roller diameter and bearing type to the gate’s weight and cycling frequency so the repair lasts.
Chain and Rack Adjustments
A loose chain slips and slams, a tight chain burns out motor bearings. We set the chain tension to manufacturer spec and check every master link and connecting pin for wear.
Wrought Iron Gate Repair
Wrought iron gate repair focuses on ornamental gates with decorative scrollwork, forged joints, and designer finishes. These gates are heavier than they look and hide damage at the welds and inside the posts. Carver Gate Repair Henderson frequently repairs wrought iron gates in Anthem and Seven Hills, where the HOA standards demand a repair that disappears into the original design. Invisible reinforcement work, matching paint and patina, and precise welding are the core of the job. Wrought iron gate repairs in Henderson run $200 to $800 depending on the extent of ornamental work involved, and our written quote covers the full restoration, never a bare weld.
Ornamental Match Work
Manufacturers and patterns change, and matching a twelve-year-old scroll requires fabrication work, not a catalog order. We shape replacement pieces to match your gate’s existing pattern, then finish them to blend.
Post Stabilization
A wrought iron gate is only as solid as the post holding it. When posts lean or twist, we dig, reset, and backfill with concrete, then verify the gate swings on level hinges again.
Metal Gate Repair
Metal gate repair covers steel, aluminum, and tubular gates of any design, from simple pool gates to full panel driveway gates. We see three problems most often in Henderson: bottom rails rusting from irrigation overspray, aluminum welds cracking from repeated flexing, and hinges pulling screws out of the post. Carver Gate Repair Henderson repairs the underlying cause before touching the visible damage. Typical metal gate repairs run $120 to $450 for hinge and frame work, more when sections require cutting out and replacement. Because different metals demand different filler rod and heat, we match the welding process to the material so the repair isn’t a temporary patch.
Aluminum Repair Technique
Aluminum gates crack when the metal fatigues, and backyard repairs with the wrong rod make the crack worse. We use the correct filler material, clean the weld zone properly, and reinforce with backing plate where the original design was undersized.
Bottom Rail Replacement
Henderson’s irrigation water and soil salts destroy the bottom rail first. We cut out the rotted section, weld in matching material, and drill drain holes where water pools, so the next decade doesn’t repeat the failure.
Wood Gate Repair
Wood gate repair keeps the gate that matches your fence, entry, or side yard working without replacing the whole structure. Wood gates in Henderson face particularly harsh sun that dries and splits the boards, snaps lag screws, and warps the frame enough to bind the gate. Carver Gate Repair Henderson replaces failed hinge screws with through-bolts and tee nuts, squares and braces a sagging frame, and swaps split pickets before interior framing rots. A typical wood gate repair runs $130 to $350 for hinge and frame alignment work; full rebuilds cost more. Where a motor is involved, we coordinate with the operator mounting so the repaired gate cycles cleanly.
Frame Bracing and Squaring
A wood gate that drags has usually pulled its frame out of square. We remove the gate, square it on a flat surface, and install or replace a diagonal compression brace so it stays square under its own weight.
Hinge Pull-Out Repair
When screws strip out, the gate sags, and the next repair won’t hold without a better fastening method. We bore the stripped hole, glue and seat a hardwood plug or use through-bolts with washers, then re-hang the gate at the right height.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
Our technicians train on LiftMaster, FAAC, BFT, and Linear equipment, among the nine brands we service. LiftMaster is the most common residential operator in the Las Vegas Valley, and we carry their OEM circuit boards, gears, and remotes on the truck. FAAC systems appear frequently in Henderson’s gated communities, where hydraulic and electromechanical swing operators need specific bleeding and rotation techniques. BFT and Linear gear shows up in both residential and light commercial settings, and we keep the common failure parts for those units stocked.
We don’t take a one-brand approach: we diagnose the operator you already own and repair it correctly rather than pushing a replacement. Whether you have LiftMaster, FAAC, BFT, Linear, or any other make, we can repair it.
Signs You Need a Pro Right Now
- Gate reverses before closing fully. This usually means the safety sensor is misaligned, the force limit is set too low, or something is binding in the track. If you can’t close the gate, your property stays open; if the force setting is wrong, the gate can pin a car or person.
- Operator hums but the gate doesn’t move. A hum with no movement points to a failed capacitor, stripped gear, or an engaged manual release. Running the motor in this state burns out the windings quickly, so call before you keep pressing the remote.
- Gate slams or shudders at the stops. That’s the limit switch or travel module failing, and the gate is being driven past its end point every cycle. The hardware doesn’t absorb that shock forever.
- Visible rust at welds or bottom rail. Rust never stops on its own in an outdoor gate. The weld area weakens incrementally until the next wind gust or close cycle completes the break.
- Remote works intermittently. Intermittent operation usually means a failing receiver board, a loose antenna, or a low-voltage problem in the operator. Intermittent turns into permanent at the worst possible time, and the board replacement is simpler before it fails completely.
Our Process, Step by Step
- 1
Call and book a visit. A live person answers at (775) 307-6571, gathers the symptoms you’re seeing and the brand of operator, and books a window that works. No voicemail, no call-back queue, no waiting until Monday.
- 2
Diagnosis at the property. The technician tests the operator’s electrical draw, checks limit switch function, inspects hinges, track, and welding points, and reports exactly what failed and why. You see the findings, not just a price.
- 3
Written price before work. The repair is itemized in writing: parts, labor, and the scope of the fix. You approve the number, and that number doesn’t change. No estimate that grows once the job is open.
- 4
Repair and workmanship. The technician completes the repair, tests the gate through full open-close cycles, re-checks the safety sensors and force limits, and cleans the work area. The site looks like we weren’t there, except the gate works.
- 5
Written guarantee. Every repair carries the 365-Day Done Right Promise in writing. If the repair fails within the guarantee window, we return and make it right at no charge.
How Much Does Gate Repair Cost in Henderson?
Gate repair in Henderson typically runs $95 at the low end for a sensor realignment or remote programming, and up to $800 or more for a commercial control board replacement or welded structural repair. A typical driveway gate repair falls between $150 and $450. The variables are the type of repair, the brand of operator, and whether the gate must be removed and re-hung. Parts for LiftMaster or FAAC operators cost more than generic components, but using the correct OEM part means the repair lasts.
What affects the price: access to the operator (wall-mounted vs. underground), condition of the metal (surface rust vs. structural rot), and whether you need custom fabrication for ornamental pieces. What doesn’t affect the price: anything we discover after the job starts. The written price delivered before work begins is the price you pay, and if the tech sees additional work that matters, you approve a new written price before that work begins. Every estimate is free, and every repair that goes forward carries the 365-Day Done Right Promise.
Our Service Area Near Henderson
Carver Gate Repair Henderson covers the city of Henderson and the surrounding communities, from Gate Repair in Enterprise to Gate Repair in Spring Valley. We also serve Nellis AFB, Green Valley, Whitney, Anthem, Paradise, Sunrise Manor, Winchester, Southern Highlands, and Boulder City. Most Henderson calls are reached within a two-hour window, Monday through Saturday, with emergency service available nights and weekends through the same live-answer phone line.
Serving Henderson, NV - Our Local Coverage Area
We’re based in the Henderson area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Henderson
Gate repair is the process of fixing a gate that won’t open, won’t close, runs noisily, or moves unevenly. The work spans mechanical fixes (hinges, rollers, track, welds), electrical fixes (circuit boards, limit switches, sensors), and operator fixes (motors, chains, belts, receivers). Carver Gate Repair Henderson handles all of it, with a written price before work starts and a one-year written guarantee on every repair.
Most driveway gate repairs finish in one to two hours on site. Work that requires fabrication, welded structural repair, or a custom part can take a few days. We tell you the timeline in writing before you approve the job.
Most residential gate repairs in Henderson cost between $150 and $450. Small jobs, like a sensor realignment or remote reprogramming, can be under $100, and commercial control board replacements or structural welding can exceed $800. You receive an exact written price before any work begins. Call (775) 307-6571 and we’ll give you a straight number for your specific gate.
Yes. We carry LiftMaster OEM parts on our trucks and service every common LiftMaster wall-mount, swing, and slide operator. We also service FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems.
We keep same-day slots open for Henderson homeowners, and our phone line is answered live 24/7. If your gate is stuck open or stuck closed, state that when you call and we’ll prioritize the visit. A diagnostic appointment is scheduled before any repair is dispatched.
The 365-Day Done Right Promise covers the repair we performed, in writing, for one full year from the date of service. If the same repair fails inside that window, we return and fix it at no charge. No argument, no fine print. This is the Garrison Standard, applied at every Carver location.
Clear vehicles away from the gate, make sure the gate is in the position the technician requested, and have your remote controls available. If the gate is at a community or HOA entrance, notify the property manager so we have access. You don’t need to be present for the full repair, but you do need to approve the written price before work starts.
Schedule Your Gate Repair Service in Henderson Today
Call (775) 307-6571 for a free estimate on gate repair anywhere in Henderson. A live person answers around the clock, every day, and we’ll get you on the schedule with a written price before any work begins. The job gets done right, and it’s guaranteed in writing for a full year.
Written by Lonnie Burke, Owner at Carver Gate Repair Henderson, serving Henderson and the surrounding communities since 2008.